 |
 |
 |
 |
 |
 |
||
 |
 |
 |
 |
 |
| 5 | 1/1 | 返回列表 |
| 查看: 1089 | 回復: 3 | ||
| 當前只顯示滿足指定條件的回帖，點擊這里查看本話題的所有回帖 | ||
chiko75銅蟲 (小有名氣)
|
[求助]
ANSYS經典版中，請問如何判斷重啟動已經成功？ 已有1人參與
|
|
|
用生死單元法+重啟動模擬激光去除，雖然在后處理中觀察到特定溫度以上的單元都被殺死，但無法確定重啟動是否成功，命令rescontrol,file_summary執行后的彈窗也只能看到前3步的載荷步信息，沒有后續載荷步的信息。請問有什么直接證據可以確定重啟動已經成功？ 命令流如下： finish /clear,start /filname,restart test kill elem,0 /units,si /prep7 ET,1,SOLID70 $ ET,2,SOLID90 mptemp,1,0,25,100,200,300,400 mptemp,,500,600,700,800,820,850 mptemp,,880,915,950,1083,1200,1500 mpdata,dens,1,1,8000,7990,7973,7942,7913,7880 mpdata,dens,1,,7840,7800,7762,7710,7692,7674 mpdata,dens,1,,7650,7549,7275,7225,7045,6788 mpdata,kxx,1,1,36,36.5,37,37.5,38,38.6 mpdata,kxx,1,,39.2,39.6,40.5,41,41,50 mpdata,kxx,1,,60,80,100,200,350,500 mpdata,c,1,1,402,402.4,412,420,430,446 mpdata,c,1,,455,464,473,482,488,514 mpdata,c,1,,521,527,530,530,530,530 mpdata,enth,1,1,0,25*7990*402.4,100*7973*412,200*7942*420,300*7913*430,400*7880*446 mpdata,enth,1,,500*7840*455,600*7800*464,700*7762*473,800*7710*482,820*7692*488,850*7674*514 mpdata,enth,1,,880*7650*521,915*7549*527,950*7275*530,1000*7225*530+7225*212e3,1500*7045*530+7045*212e3,2000*6788*530+6788*212e3 w_matrix=0.05 $ l_matrix=0.08 $ h_matrix=0.010 $ h_clad=0.002 esize_ref=0.001 $ D=2*esize_ref !焊縫寬度 pi=acos(-1) dists_inc=esize_ref $ v_scan=10e-3 $ temp_preh=298.15 count=4 !l_matrix/v_scan /com,create volume block,-D/2,D/2,0,l_matrix,0,h_clad cm,clad,volu *dim,dmsn,array,8 dmsn(1)=-w_matrix/2,-6*D,-(1.5*D+2*esize_ref),-1.5*D,1.5*D,(1.5*D+2*esize_ref),6*D,w_matrix/2 *do,i,1,7 block,dmsn(i),dmsn(i+1),0,l_matrix,0,-h_matrix *enddo *del,dmsn,,nopr allsel vglue,all vsel,s,loc,x,-w_matrix/2,-6*D vsel,a,loc,x,6*D,w_matrix/2 cm,matrix_hex,volu vsel,s,loc,x,-6*D,6*D vsel,r,loc,z,0,-l_matrix cm,matrix_tet,volu allsel cmgrp,matrix,matrix_hex,matrix_tet allsel lsel,s,loc,x,-1.5*D,1.5*D lesize,all,esize_ref lsel,s,loc,x,-(1.5*D+esize_ref) lsel,a,loc,x,(1.5*D+esize_ref) lsel,u,tan1,z,1 lsel,u,tan1,z,-1 lesize,all,esize_ref lsel,s,loc,x,-4*D,-w_matrix lsel,a,loc,x,4*D,w_matrix lsel,r,loc,z,-h_matrix/2 lesize,all,4*esize_ref lsel,s,loc,x,-4*D,-w_matrix lsel,a,loc,x,4*D,w_matrix lsel,r,tan1,z,0 lesize,all,4*esize_ref mat,1 $ type,1 $ mshkey,1 $ mshape,0 vmesh,clad vmesh,matrix_hex type,2 $ mshkey,0 $ mshape,1 vmesh,matrix_tet numcmp,area vimp,matrix_tet,0,3 vsel,s,,,clad eslv,s,1 cm,elem_clad,elem allsel save /solu antype,4 timint,1,therm solcontrol,on,, tintp,,,,1,,,,,, thopt,full,0.05,64 trnopt,full nropt,full,,on pred,on,,on kbc,0 lumpm,0 lnsrch,1 autots,0 ncnv,2 outres,basic,last outpr,all,all tunif,temp_preh allsel nsel,s,loc,z,-h_matrix sf,all,conv,5,temp_preh asel,s,loc,z,-h_matrix+0.0001,0-0.0001 asel,r,ext sfa,all,,conv,20,temp_preh asel,s,ext asel,r,loc,z,0 sfa,all,,conv,40,temp_preh allsel t=1e-4 time,t deltim,5e-5,5e-5,5e-5 solve count_step=0 rescontrol,define,all,5 num_killelem=50 *dim,kill_elem,,num_killelem parsav,all,parareco,txt *do,i,0,count !后處理命令插入點 !****************** !在非重啟動中可被刪去 /post1 set,last allsel etable,temp_elem,temp esel,s,,,elem_clad esel,r,live esel,r,etab,temp_elem,653,3000 *get,num_killelem,elem,,count *get,min_killelem,elem,,num,min nsle,s,1 *get,maxy_kill,node,,mxloc,y *do,ii,1,num_killelem kill_elem(ii)=min_killelem min_killelem=elnext(min_killelem) *enddo parsav,all,parareco,txt save !****************** /solu antype,,rest !在非重啟動中可被刪去/被注釋掉 parres,new,parareco,txt !在非重啟動中可被刪去/被注釋掉 trnopt,full allsel !殺死單元命令插入點 !****************** !在非重啟動中可被刪去 *if,num_killelem,gt,0,then *do,ii,1,num_killelem ekill,kill_elem(ii) *enddo *endif allsel *if,maxy_kill,gt,esize_ref,then esel,s,,,elem_clad nsle,s,1 nsel,r,loc,y,maxy_kill,0 esln,r,1 ekill,all *endif allsel !****************** !****************** !瞬時求解，只用于在后處理中觀察單元是否被殺死，可刪除 BFDELE,all,HGEN t=t+1e-4 time,t solve !****************** count_step=count_step+1 disy=i*dists_inc*2 t=(disy+dists_inc)/v_scan !BFDELE,all,HGEN!瞬時求解中可被刪去/被注釋掉 esel,s,,,elem_clad nsle,s,1 nsel,r,loc,y,disy-dists_inc,disy+dists_inc,0.00001 bf,all,hgen,6e10 time,t nsubst,5,50,5,1 allsel SOLVE rescontrol,file_summary !在非重啟動中可被刪去/被注釋掉 save *ENDDO !省略最后一次后處理的命令 |
回復此樓» 猜你喜歡
售SCI一區T0P文章，我:8.O.5.5.1.O.5.4,科目齊全,可+急
已經有7人回復
-
（081700）化學工程與技術-298分求調劑
已經有4人回復
-
求調劑
已經有5人回復
-
一志愿中科大材料與化工。353分能調劑到哪？
已經有7人回復
-
337一志愿華南理工0805材料求調劑
已經有5人回復
-
伙伴們，祝我生日快樂吧
已經有4人回復
-
301求調劑
已經有3人回復
-
材料與化工304求B區調劑
已經有4人回復
-
讀博申請
已經有7人回復
-
一志愿江南大學085701環境工程專碩總分287求調劑
已經有5人回復
4樓2023-11-30 09:29:10
2樓2023-11-20 09:07:05
chiko75
銅蟲 (小有名氣)
- 應助: 0 (幼兒園)
- 金幣: 235.7
- 散金: 3
- 帖子: 241
- 在線: 34.7小時
- 蟲號: 19623564
- 注冊: 2019-11-06
- 性別: GG
- 專業: 金屬基復合材料
3樓2023-11-24 17:58:40
| 最具人氣熱帖推薦 [查看全部] | 作者 | 回/看 | 最后發表 | |
|---|---|---|---|---|
|
[考研] 材料工程,326分，求調劑 +4 | KRSLSR 2026-03-10 | 4/200 |
|
|---|---|---|---|---|
|
|
[考研] 材料與化工（0856）304求B區調劑 +6 | 邱gl 2026-03-10 | 9/450 |
|
|
[考研] 大連大學化學專業研究生調劑 +3 | 琪久. 2026-03-10 | 8/400 |
|
|
|
[考研] 考研材料與化工，求調劑 +7 | 戲精丹丹丹 2026-03-09 | 7/350 |
|
|
|
[考研] 材料調劑，307分 +12 | 張泳銘1 2026-03-09 | 13/650 |
|
|
|
[考研] 化工0817調劑 +8 | 燦若星晨 2026-03-10 | 8/400 |
|
|
|
[考研] 298求調劑 +3 | Vv呀！ 2026-03-10 | 3/150 |
|
|
|
[考研] 311求調劑 +3 | 牛乳糖的卡卡 2026-03-10 | 3/150 |
|
|
|
[考研] 0817化學工程319求調劑 +7 | lv945 2026-03-08 | 9/450 |
|
|
|
[考研] 085600材料與化工 326 求調劑 +4 | 熱愛生活ing 2026-03-09 | 4/200 |
|
|
|
[基金申請] 面上項目還需要AI說明嗎？ +3 | liyundong 2026-03-08 | 3/150 |
|
|
|
[考研] 一志愿山東大學，總分327，英語二79，有論文，有競賽，已過四六級 +3 | 木木目目1 2026-03-09 | 3/150 |
|
|
|
[考研] 337求調劑 +3 | 睡醒，。 2026-03-09 | 3/150 |
|
|
|
[考研] 303求調劑 +8 | forgman95 2026-03-05 | 10/500 |
|
|
|
[考研] 材料科學（0805）338 求調劑 +7 | xiaokang3286 2026-03-07 | 7/350 |
|
|
|
[考研] 306求調劑 +7 | Bahati 2026-03-05 | 7/350 |
|
|
|
[考博] 2026年博士名額撿漏 +4 | 科研ya 2026-03-04 | 7/350 |
|
|
|
[考研] 08工科求調劑 +3 | 隆LLL 2026-03-06 | 4/200 |
|
|
|
[考研] 材料與化工354調劑 +4 | Lucy-xiao 2026-03-06 | 7/350 |
|
|
|
[考研] 求調劑，學校研究所都可以，材料與化工267分 +6 | wmx1 2026-03-05 | 6/300 |
|